fiestaturbo.com

[FIESTA_NEO]

They look good

[FIESTA_NEO]

They look good

[Philie*RST]

i want one too they looks TOP , 100% having a set

[j7aoc]

It's got to go back as it's not fitting 100% but theses are the picture's. I didn't fit the gauge's which would of looked better as there no point till it fit's

[Philie*RST]

MMMM haha i want them in black

[Pookz]

Wouldn't it look great if it was in the same finish as the clock next to it?

[j7aoc]

What like this? Im going to ask them if they can do it in a grey carbon

[Philie*RST]

thats f**kin sexy

[Brammer]

I just bought an auto specialist two gauge and ACT , the only thing with these is theirs no ACT option which would have been better but i guess they will see how they sell and possibly bring in new ideas

Don't think there's room but if you gave me the measurements i could tell you. Could look into getting one made in place of the clock?

No problem when this new i have comes i'll send you the measurements.

[TIL13R]

What like this? Im going to ask them if they can do it in a grey carbon

Like that alot!

[mk3modda]

i would have one 100% if they were the same colour as the clock .
not sure i like the carbon look against the rest of the dash

[Excursion]

It's really nice to see a decent product being made for the aftermarket, it's rare!

A couple of points:

1) Ideally they want angling towards the driver
2) when fitted, make sure the vent is blanked off to prevent any dirt getting in to the gauges.

[Ram]

they both look awsome

not sure which i prefer. carbon looks good, but the black matches the clock. hhhmm.

[j7aoc]

mk3modda: Im thinking the same as i think the carbon would look better on a black dash and the satin finish one would look bettter on the grey dash you can get a light grey carbon so the guy is going to give me a ring tomorrow so i will ask

Excursion: I will ask about the angling

[mk3modda]

whats happening with these? i want a black one

[j7aoc]

Had a few problems with getting it to fit perfectly. But all is sorted now should get it back this week and let you all know with an update

[heeman10]

A couple of points:

1) Ideally they want angling towards the driver
2) when fitted, make sure the vent is blanked off to prevent any dirt getting in to the gauges.

A little like mine?

Angled:



Blanked:



Do I get a special star?

[j7aoc]

I might be looking into getting them to do some thing with the clock

[j7aoc]

I've been sent my new one and it fit's very well and is a tight fit which is what we wanted i haven't had time to fit any gauge's as my car is in bit's and im trying to get it all done for f.i.t.p but i have asked barry who made the gague holder if you/we can have a group buy they haven't start producing them yet but will be available in real carbon fiber or carbon fiber but black finish

[cosmagedon]

I will defo have one

[j7aoc]

I will defo have one

Your name is now on the list on page 1

[Project_XR2i_Trackcar]

I would really like one of these but, if possible......

Is there any chance they can do one that extends to fill the clock space too and therefore allow for 3 gauges?

ie like S1's below (note: i'm refering to the holder size, not the actual gauge layout)..........



I'd rather have one like that and i would happily pay the extra for it.

Also, how long is the turn around on these and who is the order/payment through.

PS. S1, hope you don't mind me borrowing your pic

[j7aoc]

Don't think fitting 3 in and taking out the clock will be poss as they will have to make a mold and just for one person this will cost to much and take to long they might be looking at getting a ACT gauge where the clock fit's

[j7aoc]

They will be selling these soon for £27+ p+p but i've asked for a group buy

[Project_XR2i_Trackcar]

Don't think fitting 3 in and taking out the clock will be poss as they will have to make a mold and just for one person this will cost to much and take to long they might be looking at getting a ACT gauge where the clock fit's

bummer

i'll keep an eye on this thread and think about the 2 pod one in the meantime then. My clock got binned ages ago - weight i didnt need.

[j7aoc]

Anyone???? Im not no bothered as i have mine

[mk3modda]

i want one but what does the black finish look like? i want it looking the same as the clocks finish. like a matt black ?

if so ill have one please

[j7aoc]

i want one but what does the black finish look like? i want it looking the same as the clocks finish. like a matt black ?

if so ill have one please

Sorry but i haven't had one to look at yet but it look's like this It's about as good as you are going to get when using carbon when the clock are plastic and the holder is new and the clock will be about 16 year's old but like i said think they might be doing some thing with the clock. I will add you to the list

[McGoo 69]

id deffo have one if they made one what removed the clock and replaced it with a round anologue clock to match the guages

what guages could i run for my si lol

[knuckles]

Does the guage holder have proper mounts which clip in like the vent ?

[TIL13R]

Il have one please!

Tiller

[j7aoc]

Does the guage holder have proper mounts which clip in like the vent ?

You mean to stop it falling out of the dash then yes that's why it has taken so long it's all built on to the holder and is all carbon like i said before thing is so light is unreal TIL13R you have been added

[mk3modda]

id deffo have one if they made one what removed the clock and replaced it with a round anologue clock to match the guages

what guages could i run for my si lol

i have digital SPA guages and the match the clock perfectly

[j7aoc]

Any more poeple want one

[Philie*RST]

me. in blak please mate. my msn is hawittp@hotmail.co.uk add me matey and give me details to send a check